Your Personal 2 Minute Quiz

Take our two minute questionnaire to Discover your perfect style and get your reno underway with Beaumont’s What’s My Style! It’s jam packed with inspired designs, style advice and knockout products to help you renovate and style like a star.


Our Style Guru Naomi Findlay

She is Australia’s rapid renovation expert and recognised internationally for beautiful, healthy and wealthy designs. In fact there’s nothing Naomi loves more than helping people maximize the sale value of their property. Naomi is the wiz behind the What’s My Style 2 Minute Quiz.


Our Team of Stylists

Say hello to our star studded line-up of Australia’s most popular stylists and renovators! You’ve seen their amazing work on smash TV shows like The Block, Renovation Rumble and The Living Room. They’re here to help you achieve a rock star reno!


Welcome back


If you've read our entire How to Tile DIY Guide, you'll now be an expert in DIY tiling, but even if you haven't, these 15 Top Tips (and the top 10 reasons for tile fixing failures below) will come in handy for your tiling project:

Our Top 15 Tips

  • Tiles must be dry and the back of the tile clean.

  • The surface being tiled should be true and even and free from grease, wax, oil, curing compounds, and all forms of contamination.

  • Adhesive should be applied using the appropriate notched trowel. Do not use the spot fixing method, and always apply adhesive horizontally with a notched trowel, rather than in a swirling motion.

  • The whole back of each tile must be in good contact with the adhesive. Press tiles firmly into the adhesive bed and ensure that no voids occurs beneath tiles.

  • Every now and then, lift a tile from the adhesive to check that complete contact with the adhesive is being made.

  • Do not fix tiles over adhesive that has been allowed to dry and form a skin

  • Allow the adhesive to set before grouting: usually no less than 24 hours. During this time the tiles must be protected from potentially harmful factors like weather and water penetration.

  • Adhesives must be used strictly in accordance with the manufacturer's instructions.

  • To achieve greater adhesion and a longer open time, porous concrete should be dampened with water prior to tiling with cement based adhesives.

  • Any loose powder on the backs of tiles should be removed.

  • Appropriate movement joints must be used and construction joints must not be tiled over. Find out more: What Surfaces Can You Tile On?.

  • For thin bed fixing of tiles, the minimum finished thickness of the adhesive should not be less than 3mm.

  • Hairline cracks of up to 2mm in concrete should be bridged. Clean and prime the surface, allow to dry, and apply a liberal coat of ABA Barrierflex as a one-to-one mixture. Embed a reinforcement mat and immediately apply a second coat of Barrierflex. Allow to cure before tiling.

  • Tiles must never be stored in direct sunlight prior to fixing.

  • Different tiles have different amounts of variation between each piece. Always check the V Rating on your tiles and dry lay them prior to lay them if your tiles are rated V3 or V4.

The Top 10 Reasons for Tile Fixing Failures

  • Incorrect or no expansion joints: failure to use the correct expansion joints and tiling over construction joints will make your tiles too rigid, and they will crack during movement or expansion and contraction of the building.

  • Incorrect choice of adhesive. This is one of the most common causes of tile fixing failure that we see. See our page on How to Choose Grout and Adhesives for more information.

  • Allowing the adhesive to dry out before fixing the tiles.

  • Contaminated background. Ensure that the surface and area that you are tiling is properly cleaned before commencing tiling.

  • Poor or incorrect surface preparation.

  • Poor adhesive coverage. This can result from not using the correct notched trowel, using the spot fixing method, or allowing voids behind the tiles.

  • Unsatisfactory bed thickness. Ensure that you use the correct notched trowel when applying adhesive.

  • Excessive movement in the substrate.

  • Dust or loose backwash not removed from the backs of tiles. Ensure that the backs of tiles are clean and dry before laying tiles.

  • Incorrect mixing ratio of adhesive powder and liquid. Always follow the manufacturer's directions, and always add the adhesive to the water to ensure a smooth mixture.